Trailer Light Tester, 7 Pin Trailer Plug Tester with LED
Trailer Light Tester, 7 Pin Trailer Plug Tester with LED
BUNDLE & SAVE
Couldn't load pickup availability
Safe & Secure Checkout
256-bit SSL encryption
protects every order.
30-Day Guarantee
Love it or get a full
refund. No hassle.
Trailer Light Tester, 7 Pin Trailer Plug Tester with LED
š¦ Trailer light trouble, solved in seconds
Trailer Lights Out? Know If Itās Your Truck or Your Trailer.
Plug this tester into your truckās 7-way socket, switch on your lights, and read six labeled LEDs. No multimeter. No wiring know-how. No more guessing on the side of the road.
š© You Did Everything Right. The Trailer Still Wonāt Light Up.
The boatās strapped down. The coolerās packed. Everyoneās in the truck. You tap the brakes for one last check, and the trailer stays dark.
Now the guessing starts. A bulb? A blown fuse? A bad ground? Corroded pins? The truckās wiring? Those problems sit on both sides of the hitch, and with no way to rule half of them out, you end up checking everything.
Skipping it isnāt an option either. Most states require working tail, brake and turn lights on anything you tow, and a dark trailer at night is exactly what the driver behind you canāt see.
Without a tester
ā Crawling behind the trailer with a flashlight in your teeth
ā Swapping bulbs that were never the problem
ā Losing an hour, or the whole trip
ā Risking a ticket, or a rear-end collision
With this tester
ā Plug in at the truck and read the LEDs
ā Know in seconds which side has the fault
ā Fix the right thing the first time
ā Pull out on time with every light confirmed
š§ One Plug Cuts the Problem in Half
Ask any trailer tech and youāll hear the same thing: a bad ground is the number one cause of trailer light trouble, and it usually lives on the trailer. This tester checks your truckās socket first, so you know exactly which side to work on.
LED lights up
Your truck is doing its job. The fault is on the trailer, so go straight to the ground wire, the bulbs and the plug pins.
LED stays dark
The fault is on the truck side. Check the fuse, the socket, the wiring or the brake controller.
š“ Six circuits. Six labeled LEDs.
Every LED is printed with the circuit it checks, so you read the result at a glance. No chart to decode, no manual to dig out of the glovebox.
ā”
Answers in seconds
Plug in, switch on, look. Each circuit shows its result the moment it gets power.
š§°
No tools, no skills
No multimeter, no wiring diagram, no probing wires. If you can turn on your headlights, you can use it.
š
Test before you hitch
Check your truck in the driveway before the trailer is even connected, not miles from home.
š
Every 7-way function
Tail and marker lights, left and right turn/brake, electric brakes, back-up lights and 12V auxiliary power.
š”ļø Built to Live in Your Truck. Built to Read True.
A tester is only as good as its connection. If the contacts are weak, an LED can stay dark on a circuit thatās actually fine, and you end up chasing a problem that isnāt there.
Brass pins for a solid connection
The pins seat firmly in your truckās socket for a stable signal, so what the LEDs show is what your truck is really sending.
Tough matte ABS shell
ABS plastic and copper construction stands up to weather, corrosion and the everyday knocks of riding in a truck.
Glovebox size
About 5.2 inches long. Keep it in the glovebox or the toolbox so itās there the day you need it.
⨠Three Steps. No Guesswork.
Plug it in
Push the tester into your truckās 7-way socket until it seats firmly.
Switch on one function at a time
Each LED lights when its circuit gets power:
TM Ā Tail & marker lights
Turn on: headlights or parking lights
LT Ā Left turn & brake
Turn on: left signal or brake pedal
RT Ā Right turn & brake
Turn on: right signal or brake pedal
BK Ā Electric brakes
Turn on: brake controller (pedal or manual lever)
BU Ā Back-up lights
Turn on: reverse, with the parking brake set
12V Ā Auxiliary power
Turn on: ignition on or engine running
Read the LEDs
Lit means that circuit is good. Dark means that circuit has a problem on the truck side. All six check out? Head straight to the trailer.
Unplug and store
Close the socket cover and drop the tester back in the glovebox for next time.
š” Testing alone? Prop your phone up to record the LED face while you work the brake pedal and shift into reverse, then watch the replay.
šļø Check Before Every Tow
Ten seconds in the driveway is all it takes, whatever youāre pulling.
š¤ Boat trailers
Ramp water and road salt are hard on plugs and grounds. Check before every launch.
šļø Campers & RVs
Confirm the truck is ready before a long haul with the family on board.
š§° Utility & work trailers
Hitching up every day? Rule out the truck in seconds and get to the job site.
š¦ ATV & hunting trailers
Early starts and dark back roads. Know your lights work before you leave.
š§ Just installed new hitch wiring? Confirm every circuit before your first tow.
Compatibility: works with trucks, SUVs and RVs that have a standard 7-way RV blade socket. The tester checks the vehicle side, so the trailer can be any type.
Why Towers Keep One in the Truck
āĀ Tells you truck or trailer in seconds
āĀ Six clearly labeled LEDs, no chart needed
āĀ Tests all six 7-way functions, including electric brakes
āĀ No batteries, no multimeter, no wiring skills
āĀ Brass pins and a tough ABS shell
āĀ Small enough for any glovebox
š The gift heāll actually use
Know someone who tows a boat, a camper or a work trailer? This is the tool theyāll reach for every season. Grab one for the truck and one for the toolbox.
ā Frequently Asked Questions
Will it fit my truck?
It fits the standard 7-way RV blade socket used on most pickups, SUVs and RVs. It does not fit 7-way round-pin sockets (common on semi trucks) or 4-pin flat connectors.
Does it test my trailerās lights?
It tests the truck side. Thatās what makes it fast: if every circuit checks out, you know the problem is on the trailer and can start with the ground wire, bulbs and plug pins.
Does it need batteries?
No. It runs on the power coming from your truckās socket.
Can I test everything by myself?
Headlights, turn signals and 12V power are easy to check alone. For the brakes and reverse, have someone in the cab, or record the LED face with your phone while you work the pedal.
What if an LED stays dark?
Check that circuitās fuse first, then look for dirt or corrosion in the socket, then the wiring. If BK stays dark, make sure your brake controller is connected and set up.
Will it work on newer trucks?
It works on most trucks. Some newer models with smart trailer modules or lamp-out monitoring look for the electrical load of a real trailer, and a tester draws very little power. On these, an LED may flicker or blink even when the wiring is fine. If that happens, confirm with your trailer connected.
Which way do the LEDs face?
It depends on how your truckās socket is mounted. If the LED face points toward the ground, a quick look from below or a photo with your phone does the job.
Ten Seconds in the Driveway Beats an Hour on the Shoulder.
Hitch up knowing every light works, every time.
Choose your bundle
